Panels should not be arranged immediately after purchase - better to wait with this for two to three days. During this time the panels should be in the room where you will be placed to be "acclimatized". one must remove the foil, in which they are packaged, but it is better not to remove the bands or cords, which are related in the packets - because if you lay a loose plank, could further dry up on one side and a pervert.
What lay beneath
panels should to put on a level and dry surface. To protect the panels against penetration of moisture from the concrete surface, it can be decomposed into a special foil. Then you can put sound insulation with felt or cork boards. Special mats to lay the panels also offer manufacturers panels.
Floating floor
most important rule when laying the panels - they are arranged as a floating floor, which means it does not stick to them permanently, or to the ground, nor to the walls. Between
floor and the wall must be left to the slot. The panels may not fit tightly against the walls, because when under the influence of changing weather conditions will increase the volume of the floor, she will break the welds or wybrzuszy the middle of the room.
second important principle that must be considered before applying the panels - you have to put them in the direction of incidence of sunlight, which is perpendicular to the window. Thanks to this place joins the panels will become less pronounced.
How is the panel
first The first board panels must be placed in a corner in such a way that both sides of the groove were the walls.
second You have to remember to leave an expansion gap between the board and the wall. This is usually about 1-2 cm. For the determination of the expansion joint used in plastic or wooden wedges inserted tightly between the wall and the panels, when laid across the floor removed them.
third If the government does not stop flush with the end of the panel, it has to be cut. This should be done as follows - an element that will cut, arranged in a row so that the pen was next to the pen, pointed in the right place and cut off, then turn again to page cut was on the wall. The rest of the severed part begins the next government.
4th If the question is how the glue is applied - the tongue or the groove - opinions are divided. Most assumed that if the panels are laminated, the adhesive should be applied to the pen, if laminated - on top of the gully.
5th After laying first three rows should be squeeze clamp assembly and leave for several hours and only after that lay successive rows.
6th Further boards can knock with a hammer and wooden block. But you can not knock the edge of the shoe with a tongue so they are not damaged.
7th Pushing the panels, you must be careful not to do it too much, otherwise it can "jump" to the top of the eighth
If the board is pressed down, next comes the glue on their surface, have to wipe with a damp cloth, so as to not bleed. Not be allowed zasechł to the surface of the panels.
9th When the whole floor is already arranged, you must leave at least 24 hours.
10th Spacers are removed when the glue dries, the edges of the floor finish finishing the baseboards. But they can not attach to the floor and walls, so as not to block the movements of the panels caused by changing weather conditions.
11th The edges of the panels in place, where they combine with another type of flooring, masks with special strips, which reduce the amount of different surfaces (eg, panels and tiles).
Laying without glue
In shops you can also find the panels that connects without using glue. They are designed tongue and groove that the snap junction. Such panels can be removed and put them again in another place. It is also possible replacement of damaged item, there is no such possibility in the case of panels assembled with glue.
How to arrange the first row of panels, if the wall is the curve?
If it turns out that the wall along which the system will be the first panel, is the curve - the deviations are a few inches - it will interfere with the proper expansion joint behavior. You can then cut the panel respectively. The best use for this purpose a wooden block with a width of required slots. You have to "push" to him a pencil and ride along the wall, transferring its inequality on the panel. Then you can cut off unnecessary jigsaw piece.
Attention! Jigsaw need to keep the bottom layer of the panel, so as not to damage the surface .
source: http://dom.gazeta.pl/Ladny-Dom/1, 73936.392944. Html
0 comments:
Post a Comment